circuit's design

How do i calculate the frequency of an fm transmitter circuit?

up vote -1 down vote favorite

Below is an FM transmitter circuit I found on the web that I would like to build from scratch. How I would calculate the carirer signal frequency so that I know where to tune my FM radio? If I want this to transmit my own signal, instead of the microphone signal, could I just replace the microphone with the output of a TRS connector? circuit frequency transmitter fm shareimprove this question edited Jun 7 '12 at 18:42 CyberMen 614211 asked Jun 7 '12 at 14:40 Someonation 133

3   You want to build it and you don't even know the frequency? Anyway, if you want to broadcast in the FM band (88MHz - 108MHZ for Belgium), you'll need a license and a much better schematic. Crystal stable frequency to start with. – stevenvh Jun 7 '12 at 14:44 i want to build a remote control that sends a radio wave to an other circuit that is supposed to pick up on this wave, so i need to know the frequency to adjust the reciver – Someonation Jun 7 '12 at 14:55 L1/C2 form a resonant circuit, but since L1 doesn't have a value it doesn't have a resonance frequency either. – stevenvh Jun 7 '12 at 15:02 2   Are you constrained by the receiver? If you are trying to achieve just a transmitter/receiver RF pair, then 434MHz or similar OOK is much, much easier to do. – Cybergibbons Jun 7 '12 at 15:27

2 Answers

active oldest votes

up vote 5 down vote accepted

F = 1/(2*pi*sqrt(L*C)) L and C2 are components oscillator but this is a very awful bad circuit. 1 transistor as oscillator an as modulator is not the way to do it it isn't as stable as an regular modular transmitter for just a sine out you wont use this circuit you could look on the Internet for Colpitts oscillator Hartley oscillator clapp oscillator Meissner / armstrong oscillator Wien bridge oscillator ... or some VFO (Variable ferquency oscillator) PLL DDS ... or when is must be very stable a XTAL oscillator For just data send and receive google for 433MHZ serial data 433 psk data 433 spi ... shareimprove this answer edited Jun 7 '12 at 15:22 answered Jun 7 '12 at 15:02 on8tom 30115

the only thing i want it to do is to send a single wave (that why i asked the question about the microphone) to an other circuit a few meters away... this circuit will fail to do that as well? and just to clarify, in the formula you wrote, L is the number of turns in the coil and C is C2? – Someonation Jun 7 '12 at 15:10 L is the value in Henry of the coil , C is the value in Farad. there are a lot fo websites where you can calculate the henry's of a self wound coil. the prefix p stands for pico (Farad) and is equal to *10^-12 – on8tom Jun 7 '12 at 15:24 3   This circuit will drift badly with temperature and proximity of metal or people. – Cybergibbons Jun 7 '12 at 15:27 by the schenatics i got from google it looks more compilicated... but it was also very unclear and i'm not sure that the circuits were what i'm looking for, do you happen to know any schamatics of a simple 433MHz transmitter and receiver? – Someonation Jun 7 '12 at 16:14 i took a little project that involves a remote control, and its fun to build as much of it as i can alone... – Someonation Jun 7 '12 at 16:31

up vote 4 down vote

It's not exactly clear what you mean by "transmit a single wave, not whatever the microphone outputs". Is that OOK (On-Off Keying)? It's not worth the trouble and the money to start building a transmitter yourself (unless the purpose is in the building, not the use). Digikey lists 433MHz transmitters for around 4 dollar: This one can send data at up to 3kHz and has a range of 50m. Check the Digikey site (or another distributor) if your requirements are different. shareimprove this answer answered Jun 7 '12 at 16:35 stevenvh 87.3k5145271